Читайте также: |
|
To renew the bent steps for all ladders in holds... pcs
To weld up the crack in hold No....... mm
The surfaces of cargo holds to be sandblasted
standard SA-2,0,... m2
To apply primer on all surfaces of the holds
... m2
To apply у a 11 ho Ids food-grade paint... m2
Hatch covers Hos...
To remove the cover to the shore... pcs
Hatch cover No... to be faired
To sandblast 40 %, standard SA-2.0,... m2
To apply primer 2 coatings... m2 To apply all hatch covers food-grade paint... m2 To renew rubber gasket (packing)... m To reinstall the covers... pcs
To hose test the covers as per the register requirements
Superstructure
To be mechanically chipped 20»... m2
The chipped areas to apply primer 2 coatings
... m2
To apply white paint 2 coatings... in2
Porthole glassholder with glass to be replaced Two windows to be renewed
Steel watertight door to be faired and waterproof tested
Overhead ceiling to be removed and then refitted... m2
Accommodation Ladder
To remove to workshop... pcs To fabricate and renew stanchions... pcs, steps... pcs
To reassemble the accommodation ladders, to install on board... pcs
To test accommodation ladder together with davits under proof load... pcs
Mechanical part
Main engine
To remove the cylinder cover Nos...
To extract cylinder liners... pcs
To carry Out the inspection of beads for
defects... pcs
To submit for inspection to Register Surveyor
Замерить втулки до выпрессовки и после выпрес-
совки шт
Проверить центровку движения
Головные подшипники цилиндров К...
Отдать болты головных подшипников комплектов Снять верхние и нижние половинки подшипников
Изготовить прокладки шт
Собрать с пригонкой на краску и установить
зазоры
Мотшевые подшипники цилиндров #...
Разобрать подшипники комплектов Собрать подшипники, установить зазоры.. комплектов Шлифовка шеек по необходимости комплектов
Дизель-генератор... мощность... кВт
Отсоединить трубопроводы и арматуру
Снять цилиндровые крышки
Вынуть поршни
Выпрессовать цилиндровые втулки
Выкатать рамовые подшипники
Разобрать турбонагнетатель
После разборки детали очистить, продефекто-
вать, выполнить необходимые замеры
Заменить дефектные детали
Предъявить инспектору Регистра
Собрать двигатель и предъявить в работе
Конденсатор пара
Снять крышки
Очистить трубки со стороны пара и забортной
воды шт
Заменить протекторы, прокладки и крепежные
детали
Очистить крышки и покрыть эпоксидным составом
Собрать конденсатор, спрессовать Предъявить инспектору Регистра
Электрическая часть Кабельная трасса
Произвести перегерметизаций коллективных сальников кабельной трассы на верхней палубе
Станция попарной сигнализации "Кристалл"
Произвести дефектацию и замену неисправных датчиков в трюмах шт
Произвести замену труб защиты кабелей у комингсов трюмов Сдать станцию к работе
Электродвигатель
Разобрать, очистить, высушить обмотки и пропитать электроизоляционным лаком Заменить подшипники шт Собрать, установить на место, предъявить к работе
То calibrate the liners before extraction and after reassernbling To check centering
Block bearings of cylinders Nos....
To unbolt the block bearings sets
To remove the upper and lower parts of bearings
. sets
To fabricate gaskets pcs To reassemble, to paint-fit and to establish clearances
Crank bearing of cylinder Mos...
To open the bearing sets
To reassemble the bearings, to establish clearances sets To polish the pins if necessary. sets
Diesel-generator...power... KM
To disconnect piping and fittings
To remove cylinder cover
To take out piston
To extract cylinder liners
To take out main bearings
To open the turbocharger
After dismantling, all parts to be inspected
for defects, to take readings
To renew the defective parts
To submit for inspection to Register Surveyor
To reassemble and commission the engine
Steam condenser
To remove covers
To clean the tubes from steam side and sea
water side
To renew protectors, gaskets, bolts and nuts
To clean the covers and to apply epoxy compos i tion coating
Condenser to be reassembled and to pressure To submit for inspection to Register Surveyor
Дата добавления: 2015-09-11; просмотров: 22 | Поможем написать вашу работу | Нарушение авторских прав |